-
Description
-8 × 10/100M PoE ports,1 × Gigabit RJ45 port
-Total PoE Power Budget 110 W
-Support 802.1Q VLAN
-Support PoE watchdog to detect and restart the cameras that do not respond
-Support STP/RSTP Loop prevention
-Support cable detection to locate failure
-Up to 300 m Long Range PoE Transmission
-6 kV Surge Protection
|
DS-3E1309P-EI
|
||||||||
| Shell | Metal material, fan-free design | |||||||
| Net Weight | 0.35 kg (0.77 lb) | |||||||
| Gross Weight | 1.114 kg (2.45 lb) | |||||||
| Dimensions (W × H × D) | 170.00 mm × 27.60 mm × 93.10 mm (6.69'' × 1.09'' × 3.67'') | |||||||
| Operating Temperature | 0 °C to 40 °C (32 °F to 104 °F) | |||||||
| Storage Temperature | –40 °C to 85 °C (–40 °F to 185 °F) | |||||||
| Operating Humidity | 5% to 95% (no condensation) | |||||||
| Relative Humidity | 5% to 95% (no condensation) | |||||||
| Power Supply | 54VDC，2.22A | |||||||
| Max. Power Consumption | 120 W | |||||||
| Power Consumption in Idle | 10 W | |||||||
| Installation Mode | Desk-Mounted,Wall-Mounted | |||||||
| Surge Protection | 6 KV | |||||||
|
Network Parameters |
||||||||
| Ports | 8 × 10/100 Mbps PoE port,1 × Gigabit RJ45 port | |||||||
| MAC Address Table | 8 K | |||||||
| Switching Capacity | Whole-Device Performance: 5.6 Gbps Port Performance: 3.6 Gbps | |||||||
| Packet Forwarding Rate | Whole-Device Performance: 4.17 Mpps Port Performance: 2.68 Mpps | |||||||
| Internal Cache | 4 Mbits | |||||||
|
PoE Power Supply |
||||||||
| PoE Standard | IEEE 802.3af;IEEE 802.3at | |||||||
| PoE Power Pin | End-span: 1/2(+), 3/6(-) | |||||||
| PoE Port | PoE: Ports 1 to 8 | |||||||
| Max. Port Power | 30W | |||||||
|
Software Function |
||||||||
| Long Range |
Ports 1 to 8: up to 300 m. Long range performance may vary depend on camera model or cable condition. |
|||||||
| Port Isolation |
Ports 1 to 8: port isolation mode to improve network security Ports in an isolation group cannot communicate with each other, but they can communicate with ports outside the isolation group. |
|||||||
| PoE Watchdog |
Ports 1 to 8: auto detect and restart the cameras that do not respond. |
|||||||
| Loop Prevention |
Loop prevention is used to prevent the switching network from forming loops, which will seriously affect network communication. Disabled by default. Support 802.1D STP. Suppport 802.1w RSTP. |
|||||||
| VLAN |
VLAN is used for network scale planning and network health improvement. Support 802.1Q. Configurable VLAN ID from 1-4094. Support Trunk, Access port mode. Support Max. 4094 VLAN. |
|||||||
| HPP |
Support one-click activation and remote management via Hik-Partner Pro. Functions supported: 1. Display the port rate. 2. Display the port bandwidth utilization rate. 3. Display the PoE power usage. 4. Display topology information. 5. Display the alarm status. 6. Restart ports and devices. 7. Enable port long-rage mode. 8. Remotely upgrade the device. |
|||||||
| System Maintenance |
Support device management via web. Support DHCP Client. Enabled by default for dynamic assignment of management IP addresses. Support Super IP, which is a fixed IP address (10.180.190.200) for direct access. Support management via Hik-Central Pro. Support remote management via Hik-Partner Pro. Support cable detection. Abnormal open circuits and short circuits as well as network cable length can be detected. Supports 802.1ab LLDP for peer device discovery. Support port mirroring for fault locating. |
|||||||
|
Approval |
||||||||
| EMC |
CE-EMC (EN 55032: 2015+A11: 2020, EN IEC 61000-3-2: 2019, EN 61000-3-3: 2013+A1: 2019, EN 50130-4: 2011+A1: 2014, EN 55035: 2017+A11: 2020),IC (ICES-003: Issue 7:2020),RCM (AS/NZS CISPR 32: 2015) |
|||||||
| Safety |
CB (AMD1:2009, AMD2:2013, IEC 62368-1: 2014 (Second Edition), CE-LVD (EN 62368-1: 2014+A11: 2017) |
|||||||
| Chemistry |
CE-RoHS (2011/65/EU),WEEE (2012/19/EU),Reach (Regulation (EC) No.1907/2006) |
|||||||
